1. smartctl 5.41 2011-06-09 r3365 [i686-linux-3.0.4-pmagic] (local build)
  2. Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
  4. === START OF INFORMATION SECTION ===
  5. Device Model: TOSHIBA MQ01ABD032
  6. Serial Number: 52ICS6XSS
  7. LU WWN Device Id: 5 000039 405b86ed7
  8. Firmware Version: AX002J
  9. User Capacity: 320,072,933,376 bytes [320 GB]
  10. Sector Sizes: 512 bytes logical, 4096 bytes physical
  11. Device is: Not in smartctl database [for details use: -P showall]
  12. ATA Version is: 8
  13. ATA Standard is: Exact ATA specification draft version not indicated
  14. Local Time is: Sun May 11 16:22:16 2014 UTC
  15. SMART support is: Available - device has SMART capability.
  16. SMART support is: Enabled
  18. === START OF READ SMART DATA SECTION ===
  19. SMART overall-health self-assessment test result: PASSED
  21. General SMART Values:
  22. Offline data collection status: (0x00) Offline data collection activity
  23. was never started.
  24. Auto Offline Data Collection: Disabled.
  25. Self-test execution status: ( 112) The previous self-test completed having
  26. the read element of the test failed.
  27. Total time to complete Offline
  28. data collection: ( 120) seconds.
  29. Offline data collection
  30. capabilities: (0x5b) SMART execute Offline immediate.
  31. Auto Offline data collection on/off support.
  32. Suspend Offline collection upon new
  33. command.
  34. Offline surface scan supported.
  35. Self-test supported.
  36. No Conveyance Self-test supported.
  37. Selective Self-test supported.
  38. SMART capabilities: (0x0003) Saves SMART data before entering
  39. power-saving mode.
  40. Supports SMART auto save timer.
  41. Error logging capability: (0x01) Error logging supported.
  42. General Purpose Logging supported.
  43. Short self-test routine
  44. recommended polling time: ( 2) minutes.
  45. Extended self-test routine
  46. recommended polling time: ( 83) minutes.
  47. SCT capabilities: (0x003d) SCT Status supported.
  48. SCT Error Recovery Control supported.
  49. SCT Feature Control supported.
  50. SCT Data Table supported.
  52. SMART Attributes Data Structure revision number: 16
  53. Vendor Specific SMART Attributes with Thresholds:
  54. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
  55. 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
  56. 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
  57. 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1068
  58. 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 2332
  59. 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
  60. 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
  61. 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
  62. 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 3810
  63. 10 Spin_Retry_Count 0x0033 146 100 030 Pre-fail Always - 0
  64. 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2320
  65. 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 2135
  66. 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 111
  67. 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 9423
  68. 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 45 (Min/Max 15/48)
  69. 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
  70. 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 8
  71. 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 1
  72. 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
  73. 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
  74. 222 Loaded_Hours 0x0032 092 092 000 Old_age Always - 3298
  75. 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
  76. 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
  77. 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 251
  78. 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
  80. SMART Error Log Version: 1
  81. ATA Error Count: 1319 (device log contains only the most recent five errors)
  82. CR = Command Register [HEX]
  83. FR = Features Register [HEX]
  84. SC = Sector Count Register [HEX]
  85. SN = Sector Number Register [HEX]
  86. CL = Cylinder Low Register [HEX]
  87. CH = Cylinder High Register [HEX]
  88. DH = Device/Head Register [HEX]
  89. DC = Device Command Register [HEX]
  90. ER = Error register [HEX]
  91. ST = Status register [HEX]
  92. Powered_Up_Time is measured from power on, and printed as
  93. DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
  94. SS=sec, and sss=millisec. It "wraps" after 49.710 days.
  96. Error 1319 occurred at disk power-on lifetime: 3758 hours (156 days + 14 hours)
  97. When the command that caused the error occurred, the device was active or idle.
  99. After command completion occurred, registers were:
  100. ER ST SC SN CL CH DH
  101. -- -- -- -- -- -- --
  102. 40 41 08 a0 4e 19 40 Error: WP at LBA = 0x00194ea0 = 1658528
  104. Commands leading to the command that caused the error were:
  105. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  106. -- -- -- -- -- -- -- -- ---------------- --------------------
  107. 61 08 88 90 6d 76 40 00 00:39:44.250 WRITE FPDMA QUEUED
  108. 61 00 c8 f8 9e 7b 40 00 00:39:40.457 WRITE FPDMA QUEUED
  109. 61 00 c0 f8 9d 7b 40 00 00:39:40.457 WRITE FPDMA QUEUED
  110. 61 00 b8 f8 9c 7b 40 00 00:39:40.457 WRITE FPDMA QUEUED
  111. 61 00 78 f8 9b 7b 40 00 00:39:40.457 WRITE FPDMA QUEUED
  113. Error 1318 occurred at disk power-on lifetime: 3758 hours (156 days + 14 hours)
  114. When the command that caused the error occurred, the device was active or idle.
  116. After command completion occurred, registers were:
  117. ER ST SC SN CL CH DH
  118. -- -- -- -- -- -- --
  119. 40 41 10 a0 4e 19 40 Error: UNC at LBA = 0x00194ea0 = 1658528
  121. Commands leading to the command that caused the error were:
  122. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  123. -- -- -- -- -- -- -- -- ---------------- --------------------
  124. 60 80 c0 d8 ac 77 40 00 00:39:40.304 READ FPDMA QUEUED
  125. 61 00 b8 f8 8e 7b 40 00 00:39:36.478 WRITE FPDMA QUEUED
  126. 61 00 b0 f8 8d 7b 40 00 00:39:36.478 WRITE FPDMA QUEUED
  127. 61 00 a8 f8 8c 7b 40 00 00:39:36.477 WRITE FPDMA QUEUED
  128. 61 00 a0 f8 8b 7b 40 00 00:39:36.477 WRITE FPDMA QUEUED
  130. Error 1317 occurred at disk power-on lifetime: 3758 hours (156 days + 14 hours)
  131. When the command that caused the error occurred, the device was active or idle.
  133. After command completion occurred, registers were:
  134. ER ST SC SN CL CH DH
  135. -- -- -- -- -- -- --
  136. 40 41 18 a0 4e 19 40 Error: WP at LBA = 0x00194ea0 = 1658528
  138. Commands leading to the command that caused the error were:
  139. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  140. -- -- -- -- -- -- -- -- ---------------- --------------------
  141. 61 08 a0 60 a6 83 40 00 00:39:32.371 WRITE FPDMA QUEUED
  142. 61 08 98 b8 e8 7b 40 00 00:39:32.371 WRITE FPDMA QUEUED
  143. 61 10 90 38 a4 83 40 00 00:39:32.371 WRITE FPDMA QUEUED
  144. 61 00 a0 f8 6e 7b 40 00 00:39:32.319 WRITE FPDMA QUEUED
  145. 61 00 98 f8 6d 7b 40 00 00:39:32.319 WRITE FPDMA QUEUED
  147. Error 1316 occurred at disk power-on lifetime: 3758 hours (156 days + 14 hours)
  148. When the command that caused the error occurred, the device was active or idle.
  150. After command completion occurred, registers were:
  151. ER ST SC SN CL CH DH
  152. -- -- -- -- -- -- --
  153. 40 41 80 a0 4e 19 40 Error: WP at LBA = 0x00194ea0 = 1658528
  155. Commands leading to the command that caused the error were:
  156. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  157. -- -- -- -- -- -- -- -- ---------------- --------------------
  158. 61 00 a8 f8 57 7b 40 00 00:39:32.019 WRITE FPDMA QUEUED
  159. 61 00 a0 f8 56 7b 40 00 00:39:28.188 WRITE FPDMA QUEUED
  160. 61 00 98 f8 55 7b 40 00 00:39:28.188 WRITE FPDMA QUEUED
  161. 61 00 88 f8 54 7b 40 00 00:39:28.188 WRITE FPDMA QUEUED
  162. 61 00 78 f8 53 7b 40 00 00:39:28.188 WRITE FPDMA QUEUED
  164. Error 1315 occurred at disk power-on lifetime: 3758 hours (156 days + 14 hours)
  165. When the command that caused the error occurred, the device was active or idle.
  167. After command completion occurred, registers were:
  168. ER ST SC SN CL CH DH
  169. -- -- -- -- -- -- --
  170. 40 41 d0 a0 4e 19 40 Error: WP at LBA = 0x00194ea0 = 1658528
  172. Commands leading to the command that caused the error were:
  173. CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
  174. -- -- -- -- -- -- -- -- ---------------- --------------------
  175. 61 08 78 3b 63 cd 40 00 00:39:24.026 WRITE FPDMA QUEUED
  176. 61 08 70 b8 84 83 40 00 00:39:24.026 WRITE FPDMA QUEUED
  177. 61 08 68 c0 e8 7b 40 00 00:39:24.026 WRITE FPDMA QUEUED
  178. 61 08 58 33 63 cd 40 00 00:39:24.025 WRITE FPDMA QUEUED
  179. 61 08 50 a0 7d 83 40 00 00:39:24.025 WRITE FPDMA QUEUED
  181. SMART Self-test log structure revision number 1
  182. Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
  183. # 1 Extended offline Completed: read failure 00% 3810 186207904
  184. # 2 Short offline Completed without error 00% 3809 -
  186. SMART Selective self-test log data structure revision number 1
  187. SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
  188. 1 0 0 Not_testing
  189. 2 0 0 Not_testing
  190. 3 0 0 Not_testing
  191. 4 0 0 Not_testing
  192. 5 0 0 Not_testing
  193. Selective self-test flags (0x0):
  194. After scanning selected spans, do NOT read-scan remainder of disk.
  195. If Selective self-test is pending on power-up, resume after 0 minute delay.