1. U-Boot 2015.04 (Feb 11 2016 - 15:05:00)
  3. CPU: Freescale i.MX6DL rev1.2 at 792 MHz
  4. Reset cause: POR
  5. I2C: ready
  6. DRAM: 512 MiB
  7. PMIC: device id: 0x10, revision id: 0x11
  8. PMIC: programmed
  9. MMC: FSL_SDHC: 0, FSL_SDHC: 1
  10. auto-detected panel vga-rgb
  11. Display: vga-rgb (640x480)
  12. In: serial
  13. Out: serial
  14. Err: serial
  15. Model: Toradex Colibri iMX6 DualLite 512MB V1.0A, Serial# 04869134
  16. Net: using PHY at 0
  17. FEC [PRIME]
  18. Hit any key to stop autoboot: 0
  19. Colibri iMX6 # run sd
  20. sdargs sdboot sddtbload
  21. Colibri iMX6 # run sdboot
  22. Booting from SD card
  23. reading gdt.dtb
  24. 46463 bytes read in 18 ms (2.5 MiB/s)
  25. reading uImage
  26. 4976352 bytes read in 274 ms (17.3 MiB/s)
  27. ## Booting kernel from Legacy Image at 10800000 ...
  28. Image Name: Linux-4.1.44-2.7.3+gb1555bf
  29. Image Type: ARM Linux Kernel Image (uncompressed)
  30. Data Size: 4976288 Bytes = 4.7 MiB
  31. Load Address: 10008000
  32. Entry Point: 10008000
  33. Verifying Checksum ... OK
  34. ## Flattened Device Tree blob at 12000000
  35. Booting using the fdt blob at 0x12000000
  36. Loading Kernel Image ... OK
  37. Loading Device Tree to 2df4c000, end 2df5a57e ... OK
  39. Starting kernel ...
  41. [ 0.000000] Booting Linux on physical CPU 0x0
  42. [ 0.000000] Initializing cgroup subsys cpu
  43. [ 0.000000] Initializing cgroup subsys cpuacct
  44. [ 0.000000] Linux version 4.1.44-2.7.3+gb1555bf (gumstix@sasquatch) (gcc version 6.2.0 (GCC) ) #1 SMP Tue Nov 7 17:36:46 PST 2017
  45. [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
  46. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  47. [ 0.000000] Machine model: Toradex Colibri iMX6DL/S on Gumstix Colibri Development Board
  48. [ 0.000000] Reserved memory: created CMA memory pool at 0x18000000, size 320 MiB
  49. [ 0.000000] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool
  50. [ 0.000000] Memory policy: Data cache writealloc
  51. [ 0.000000] PERCPU: Embedded 12 pages/cpu @9fb1d000 s16588 r8192 d24372 u49152
  52. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
  53. [ 0.000000] Kernel command line: enable_wait_mode=off galcore.contiguousSize=50331648 ip=off root=/dev/mmcblk1p2 rw,noatime rootfstype=ext3 rootwait fec_mac=00:14:2d:4a:4c:0e consoleblank=0 no_console_suspend=1 console=tty1 console=ttymxc0,115200n8 video=mxcfb0:dev=lcd,640x480M@60,if=RGB666 video=mxcfb1:off fbmem=8M
  54. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  55. [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  56. [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  57. [ 0.000000] Memory: 181592K/524288K available (6467K kernel code, 233K rwdata, 2112K rodata, 328K init, 416K bss, 15016K reserved, 327680K cma-reserved, 0K highmem)
  58. [ 0.000000] Virtual kernel memory layout:
  59. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  60. [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
  61. [ 0.000000] vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
  62. [ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
  63. [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
  64. [ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
  65. [ 0.000000] .text : 0x80008000 - 0x80869034 (8581 kB)
  66. [ 0.000000] .init : 0x8086a000 - 0x808bc000 ( 328 kB)
  67. [ 0.000000] .data : 0x808bc000 - 0x808f6700 ( 234 kB)
  68. [ 0.000000] .bss : 0x808f6700 - 0x8095e9a0 ( 417 kB)
  69. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  70. [ 0.000000] Hierarchical RCU implementation.
  71. [ 0.000000] Additional per-CPU info printed with stalls.
  72. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  73. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  74. [ 0.000000] NR_IRQS:16 nr_irqs:16 16
  75. [ 0.000000] L2C-310 erratum 769419 enabled
  76. [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
  77. [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
  78. [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines
  79. [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
  80. [ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB
  81. [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76050001
  82. [ 0.000000] mxc_clocksource_init 3000000
  83. [ 0.000000] Switching to timer-based delay loop, resolution 333ns
  84. [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
  85. [ 0.000023] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
  86. [ 0.001082] Console: colour dummy device 80x30
  87. [ 0.001725] console [tty1] enabled
  88. [ 0.001748] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
  89. [ 0.001788] pid_max: default: 32768 minimum: 301
  90. [ 0.001898] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  91. [ 0.001925] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  92. [ 0.002493] Initializing cgroup subsys freezer
  93. [ 0.002535] Initializing cgroup subsys debug
  94. [ 0.002571] CPU: Testing write buffer coherency: ok
  95. [ 0.002883] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  96. [ 0.002989] Setting up static identity map for 0x10008280 - 0x100082d8
  97. [ 0.004915] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  98. [ 0.005005] Brought up 2 CPUs
  99. [ 0.005055] SMP: Total of 2 processors activated (12.00 BogoMIPS).
  100. [ 0.005075] CPU: All CPU(s) started in SVC mode.
  101. [ 0.005555] devtmpfs: initialized
  102. [ 0.017292] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  103. [ 0.017717] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  104. [ 0.017778] futex hash table entries: 512 (order: 3, 32768 bytes)
  105. [ 0.035477] pinctrl core: initialized pinctrl subsystem
  106. [ 0.036524] NET: Registered protocol family 16
  107. [ 0.044493] DMA: preallocated 256 KiB pool for atomic coherent allocations
  108. [ 0.069682] cpuidle: using governor ladder
  109. [ 0.099676] cpuidle: using governor menu
  110. [ 0.099942] CPU identified as i.MX6DL, silicon rev 1.2
  111. [ 0.122264] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
  112. [ 0.122311] hw-breakpoint: maximum watchpoint size is 4 bytes.
  113. [ 0.124349] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
  114. [ 0.125512] imx-gpc 20dc000.gpc: no fsl,ldo-bypass found!
  115. [ 0.134656] SCSI subsystem initialized
  116. [ 0.134986] usbcore: registered new interface driver usbfs
  117. [ 0.135082] usbcore: registered new interface driver hub
  118. [ 0.135198] usbcore: registered new device driver usb
  119. [ 0.135405] 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator
  120. [ 0.135569] 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator
  121. [ 0.136472] i2c-gpio i2c@0: using pins 109 (SDA) and 108 (SCL)
  122. [ 0.138302] stmpe-i2c 1-0041: stmpe811 detected, chip id: 0x811
  123. [ 0.140289] i2c i2c-1: IMX I2C adapter registered
  124. [ 0.140328] i2c i2c-1: can't use DMA
  125. [ 0.140964] i2c i2c-2: IMX I2C adapter registered
  126. [ 0.141001] i2c i2c-2: can't use DMA
  127. [ 0.141142] Linux video capture interface: v2.00
  128. [ 0.141209] pps_core: LinuxPPS API ver. 1 registered
  129. [ 0.141233] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
  130. [ 0.141282] PTP clock support registered
  131. [ 0.159726] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
  132. [ 0.160924] MIPI CSI2 driver module loaded
  133. [ 0.161118] Advanced Linux Sound Architecture Driver Initialized.
  134. [ 0.162917] Switched to clocksource mxc_timer1
  135. [ 0.173972] NET: Registered protocol family 2
  136. [ 0.174803] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
  137. [ 0.174875] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
  138. [ 0.174956] TCP: Hash tables configured (established 4096 bind 4096)
  139. [ 0.175019] UDP hash table entries: 256 (order: 1, 8192 bytes)
  140. [ 0.175059] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  141. [ 0.175255] NET: Registered protocol family 1
  142. [ 0.175581] RPC: Registered named UNIX socket transport module.
  143. [ 0.175612] RPC: Registered udp transport module.
  144. [ 0.175632] RPC: Registered tcp transport module.
  145. [ 0.175649] RPC: Registered tcp NFSv4.1 backchannel transport module.
  146. [ 0.176332] CPU PMU: Failed to parse /soc/pmu/interrupt-affinity[0]
  147. [ 0.176403] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
  148. [ 0.178081] Bus freq driver module loaded
  149. [ 0.185197] VFS: Disk quotas dquot_6.6.0
  150. [ 0.185415] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  151. [ 0.187048] NFS: Registering the id_resolver key type
  152. [ 0.187102] Key type id_resolver registered
  153. [ 0.187125] Key type id_legacy registered
  154. [ 0.187164] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  155. [ 0.187713] ntfs: driver 2.1.32 [Flags: R/W].
  156. [ 0.188195] fuse init (API version 7.23)
  157. [ 0.192121] io scheduler noop registered
  158. [ 0.192163] io scheduler deadline registered
  159. [ 0.192344] io scheduler cfq registered (default)
  160. [ 0.195024] backlight supply power not found, using dummy regulator
  161. [ 0.196794] 20e0000.hdmi_video supply HDMI not found, using dummy regulator
  162. [ 0.198072] fbcvt: 640x480@60: CVT Name - .307M3
  163. [ 0.198122] mxc_sdc_fb fb@0: registered mxc display driver lcd
  164. [ 0.202745] mxc_sdc_fb fb@0: 640x480 h_sync,r,l: 64,16,80 v_sync,l,u: 4,3,13 pixclock=23750000 Hz
  165. [ 0.257217] mxc_sdc_fb fb@0: 640x480 h_sync,r,l: 64,16,80 v_sync,l,u: 4,3,13 pixclock=23750000 Hz
  166. [ 0.279629] Console: switching to colour frame buffer device 80x30
  167. [ 0.326344] mxc_sdc_fb fb@1: mxcfb1 is turned off!
  168. [ 0.330967] imx-sdma 20ec000.sdma: no iram assigned, using external mem
  169. [ 0.334751] imx-sdma 20ec000.sdma: no event needs to be remapped
  170. [ 0.338337] imx-sdma 20ec000.sdma: loaded firmware 3.3
  171. [ 0.344375] imx-sdma 20ec000.sdma: initialized
  172. [ 0.349383] pfuze100-regulator 1-0008: Full layer: 1, Metal layer: 1
  173. [ 0.353354] pfuze100-regulator 1-0008: FAB: 0, FIN: 0
  174. [ 0.356591] pfuze100-regulator 1-0008: pfuze100 found.
  175. [ 0.374111] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 24, base_baud = 5000000) is a IMX
  176. [ 1.191759] console [ttymxc0] enabled
  177. [ 1.199686] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 296, base_baud = 5000000) is a IMX
  178. [ 1.215811] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 297, base_baud = 5000000) is a IMX
  179. [ 1.232659] [drm] Initialized drm 1.1.0 20060810
  180. [ 1.241436] [drm] Initialized vivante 1.0.0 20120216 on minor 0
  181. [ 1.259707] brd: module loaded
  182. [ 1.271480] loop: module loaded
  183. [ 1.280169] spi_imx 2014000.ecspi: probed
  184. [ 1.288568] vcan: Virtual CAN interface driver
  185. [ 1.296406] CAN device driver interface
  186. [ 1.303612] spi3.0 supply vdd not found, using dummy regulator
  187. [ 1.312729] spi3.0 supply xceiver not found, using dummy regulator
  188. [ 1.333720] 2188000.ethernet supply phy not found, using dummy regulator
  189. [ 1.344214] pps pps0: new PPS source ptp0
  190. [ 1.355743] libphy: fec_enet_mii_bus: probed
  191. [ 1.363820] fec 2188000.ethernet eth0: registered PHC device 0
  192. [ 1.373292] usbcore: registered new interface driver asix
  193. [ 1.382057] usbcore: registered new interface driver ax88179_178a
  194. [ 1.391493] usbcore: registered new interface driver cdc_ether
  195. [ 1.400635] usbcore: registered new interface driver net1080
  196. [ 1.409582] usbcore: registered new interface driver cdc_subset
  197. [ 1.418636] usbcore: registered new interface driver zaurus
  198. [ 1.427242] usbcore: registered new interface driver cdc_ncm
  199. [ 1.435760] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  200. [ 1.445153] ehci-mxc: Freescale On-Chip EHCI Host driver
  201. [ 1.453437] usbcore: registered new interface driver usb-storage
  202. [ 1.462313] usbcore: registered new interface driver usbserial
  203. [ 1.470793] usbcore: registered new interface driver usbserial_generic
  204. [ 1.479884] usbserial: USB Serial support registered for generic
  205. [ 1.488516] usbcore: registered new interface driver ftdi_sio
  206. [ 1.496860] usbserial: USB Serial support registered for FTDI USB Serial Device
  207. [ 1.509449] usbcore: registered new interface driver pl2303
  208. [ 1.517855] usbserial: USB Serial support registered for pl2303
  209. [ 1.527801] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
  210. [ 1.541681] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517
  211. [ 1.558534] ci_hdrc ci_hdrc.0: EHCI Host Controller
  212. [ 1.566478] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
  213. [ 1.592965] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
  214. [ 1.602255] hub 1-0:1.0: USB hub found
  215. [ 1.609135] hub 1-0:1.0: 1 port detected
  216. [ 1.617147] mousedev: PS/2 mouse device common for all mice
  217. [ 1.634530] input: stmpe-ts as /devices/soc0/soc/2100000.aips-bus/21a4000.i2c/i2c-1/1-0041/stmpe-ts/input/input0
  218. [ 1.655105] rtc-ds1307 2-0068: rtc core: registered m41t0 as rtc0
  219. [ 1.665575] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
  220. [ 1.681589] i2c /dev entries driver
  221. [ 1.689916] mxc_v4l2_output v4l2_out: V4L2 device registered as video16
  222. [ 1.700500] mxc_v4l2_output v4l2_out: V4L2 device registered as video17
  223. [ 1.712401] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
  224. [ 1.722352] sdhci: Secure Digital Host Controller Interface driver
  225. [ 1.732297] sdhci: Copyright(c) Pierre Ossman
  226. [ 1.740322] sdhci-pltfm: SDHCI platform and OF driver helper
  227. [ 1.750575] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
  228. [ 1.761480] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
  229. [ 1.770673] sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
  230. [ 1.823087] mmc1: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
  231. [ 1.849919] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
  232. [ 1.860929] sdhci-esdhc-imx 2194000.usdhc: allocated mmc-pwrseq
  233. [ 1.875102] sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found
  234. [ 1.886961] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
  235. [ 1.938249] mmc1: new high speed SDHC card at address b368
  236. [ 1.947349] mmc4: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
  237. [ 1.962655] mmcblk1: mmc1:b368 7.46 GiB
  238. [ 1.962670] /soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified
  239. [ 1.970969] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found
  240. [ 2.000308] mmcblk1: p1 p2
  241. [ 2.012966] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
  242. [ 2.034100] mxc_vpu 2040000.vpu_fsl: VPU initialized
  243. [ 2.043465] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
  244. [ 2.061120] sdhci-esdhc-imx 2194000.usdhc: card claims to support voltages below defined range
  245. [ 2.062604] caam 2100000.caam: Entropy delay = 3200
  246. [ 2.102721] mmc4: queuing unknown CIS tuple 0x91 (3 bytes)
  247. [ 2.113425] mmc4: new high speed SDIO card at address 0001
  248. [ 2.123394] caam 2100000.caam: Instantiated RNG4 SH0
  249. [ 2.184159] caam 2100000.caam: Instantiated RNG4 SH1
  250. [ 2.192842] caam 2100000.caam: device ID = 0x0a16010000000100 (Era -524)
  251. [ 2.203261] caam 2100000.caam: job rings = 2, qi = 0
  252. [ 2.225994] mmc0: MAN_BKOPS_EN bit is not set
  253. [ 2.253223] mmc0: new DDR MMC card at address 0001
  254. [ 2.261962] mmcblk0: mmc0:0001 004GE0 3.69 GiB
  255. [ 2.270197] mmcblk0boot0: mmc0:0001 004GE0 partition 1 2.00 MiB
  256. [ 2.280126] mmcblk0boot1: mmc0:0001 004GE0 partition 2 2.00 MiB
  257. [ 2.291052] mmcblk0: p1 p2
  258. [ 2.301223] caam algorithms registered in /proc/crypto
  259. [ 2.314415] caam_jr 2101000.jr0: registering rng-caam
  260. [ 2.323976] snvs-secvio 20cc000.caam-snvs: can't get snvs clock
  261. [ 2.333339] snvs-secvio 20cc000.caam-snvs: violation handlers armed - non-secure state
  262. [ 2.347924] hidraw: raw HID events driver (C) Jiri Kosina
  263. [ 2.356824] usbcore: registered new interface driver usbhid
  264. [ 2.365632] usbhid: USB HID core driver
  265. [ 2.378099] stmpe-adc stmpe-adc: Initialized
  266. [ 2.388732] sgtl5000 1-000a: sgtl5000 revision 0x11
  267. [ 2.422493] fsl-hdmi-dai soc:hdmi_audio@00120000: failed to probe. Load HDMI-video first.
  268. [ 2.436648] fsl-hdmi-dai: probe of soc:hdmi_audio@00120000 failed with error -12
  269. [ 2.462622] imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
  270. [ 2.473802] imx-audio-hdmi sound-hdmi: initialize HDMI-audio failed. load HDMI-video first!
  271. [ 2.489832] NET: Registered protocol family 10
  272. [ 2.498794] NET: Registered protocol family 17
  273. [ 2.506631] can: controller area network core (rev 20120528 abi 9)
  274. [ 2.516298] NET: Registered protocol family 29
  275. [ 2.524170] can: raw protocol (rev 20120528)
  276. [ 2.531808] can: broadcast manager protocol (rev 20120528 t)
  277. [ 2.540995] can: netlink gateway (rev 20130117) max_hops=1
  278. [ 2.550446] Key type dns_resolver registered
  279. [ 2.559771] Registering SWP/SWPB emulation handler
  280. [ 2.569542] 2184000.usb supply vbus not found, using dummy regulator
  281. [ 2.583328] ci_hdrc ci_hdrc.1: EHCI Host Controller
  282. [ 2.591065] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
  283. [ 2.612965] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
  284. [ 2.621830] hub 2-0:1.0: USB hub found
  285. [ 2.628372] hub 2-0:1.0: 1 port detected
  286. [ 2.637249] input: gpio-keys as /devices/soc0/gpio-keys/input/input1
  287. [ 2.648117] rtc-ds1307 2-0068: setting system clock to 2000-01-01 00:00:10 UTC (946684810)
  288. [ 2.669903] ALSA device list:
  289. [ 2.675627] #0: imx6-colibri-sgtl5000
  290. [ 2.691082] EXT4-fs (mmcblk1p2): mounting ext3 file system using the ext4 subsystem
  291. [ 2.705347] EXT4-fs (mmcblk1p2): INFO: recovery required on readonly filesystem
  292. [ 2.717902] EXT4-fs (mmcblk1p2): write access will be enabled during recovery
  293. [ 2.732629] EXT4-fs (mmcblk1p2): recovery complete
  294. [ 2.757535] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
  295. [ 2.771190] VFS: Mounted root (ext3 filesystem) readonly on device 179:2.
  296. [ 2.785058] devtmpfs: mounted
  297. [ 2.791126] Freeing unused kernel memory: 328K
  298. [ 3.082638] systemd[1]: System time before build time, advancing clock.
  299. [ 3.140992] random: systemd urandom read with 24 bits of entropy available
  300. [ 3.160869] systemd[1]: systemd 230 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT +GNUTLS +ACL +XZ -LZ4 -
  301. SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
  302. [ 3.202541] systemd[1]: Detected architecture arm.
  304. Welcome to Poky (Yocto Project Reference Distro) 2.2.2 (morty)!
  306. [ 3.243744] systemd[1]: Set hostname to <colibri-imx6>.
  307. [ 3.634304] systemd[1]: Listening on Network Service Netlink Socket.
  308. [ OK ] Listening on Network Service Netlink Socket.
  309. [ 3.663154] systemd[1]: Reached target Remote File Systems.
  310. [ OK ] Reached target Remote File Systems.
  311. [ 3.693287] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
  312. [ OK ] Listening on /dev/initctl Compatibility Named Pipe.
  313. [ 3.732153] systemd[1]: Created slice System Slice.
  314. [ OK ] Created slice System Slice.
  315. [ 3.763419] systemd[1]: Listening on Journal Socket.
  316. [ OK ] Listening on Journal Socket.
  317. [ 3.804960] systemd[1]: Starting Load Kernel Modules...
  318. Starting Load Kernel Modules...
  319. [ 3.836206] systemd[1]: Starting Setup Virtual Console...
  320. Starting Setup Virtual Console...
  321. [ 3.865351] systemd[1]: Mounting Debug File System...
  322. Mounting Debug File System...
  323. [ 3.893532] systemd[1]: Created slice system-wpa_supplicant.slice.
  324. [ OK ] Created slice system-wpa_supplicant.slice.
  325. [ 3.942666] systemd[1]: Created slice system-serial\x2dgetty.slice.
  326. [ OK ] Created slice system-serial\x2dgetty.slice.
  327. [ 3.973849] systemd[1]: Created slice User and Session Slice.
  328. [ OK ] Created slice User and Session Slice.
  329. [ 4.003391] systemd[1]: Reached target Slices.
  330. [ OK ] Reached target Slices.
  331. [ 4.033632] systemd[1]: Listening on Journal Socket (/dev/log).
  332. [ OK ] Listening on Journal Socket (/dev/log).
  333. [ 4.064033] systemd[1]: Listening on udev Kernel Socket.
  334. [ OK ] Listening on udev Kernel Socket.
  335. [ 4.093591] systemd[1]: Listening on udev Control Socket.
  336. [ OK ] Listening on udev Control Socket.
  337. [ 4.123326] systemd[1]: Reached target Swap.
  338. [ OK ] Reached target Swap.
  339. [ 4.165635] systemd[1]: Mounting Temporary Directory...
  340. Mounting Temporary Directory...
  341. [ 4.195475] systemd[1]: Starting File System Check on Root Device...
  342. Starting File System Check on Root Device...
  343. [ 4.224199] systemd[1]: Created slice system-getty.slice.
  344. [ OK ] Created slice [ 4.233490] systemd[1]: Listening on Syslog Socket.
  345. system-getty.slice.
  346. [ OK ] Listening on[ 4.247240] systemd[1]: Starting Create list of required static device nodes for the current kernel...
  347. Syslog Socket.
  348. [ 4.263657] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  349. Starting Create list of [ 4.277357] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
  350. required st... nodes for the current kernel...
  351. [ OK 4.295460] systemd[1]: Starting Journal Service...
  352. m] Started Forward Password Reque[ 4.305415] systemd[1]: Reached target Paths.
  353. sts to Wall Directory Watch.
  354. [ OK ] Started Dispatc[ 4.320133] systemd[1]: Mounted Debug File System.
  355. h Password Requests to Console Di[ 4.328069] systemd[1]: Mounted Temporary Directory.
  356. rectory Watch.
  357. Starting[ 4.338891] systemd[1]: Started Load Kernel Modules.
  358. Journal Service...
  359. [ OK[ 4.349484] systemd[1]: Started Setup Virtual Console.
  360. ] Reached target Paths.
  361. [ systemd[1]: Started Create list of required static device nodes for the current kernel.
  362. [0;32m OK ] Mounted Debug File System.
  363. [ OK ][ 4.379891] systemd[1]: Starting Apply Kernel Variables...
  364. Mounted Temporary Directory.
  365. [ systemd[1]: Mounting Configuration File System...
  366. [0;32m OK ] Started Load Kernel Modules.
  367. [ OK 4.403250] systemd[1]: Mounting FUSE Control File System...
  368. m] Started Setup Virtual Console.
  369. [ OK ] Started Cr[ 4.418852] systemd[1]: Mounted FUSE Control File System.
  370. eate list of required sta...ce no[ 4.428221] systemd[1]: Mounted Configuration File System.
  371. des for the current kernel.
  372. Starting Apply Kernel Variables...
  373. Mounting Configuration File System...
  374. Mounting FUSE Control File System...
  375. [ OK ] Mounted FUSE Control File System.
  376. [ OK ] Mounted Configuration File System.
  377. [ 4.507937] systemd[1]: Started Apply Kernel Variables.
  378. [ OK ] Started Apply Kernel Variables.
  379. [ 4.546510] systemd[1]: Started File System Check on Root Device.
  380. [ OK ] Started File System Check on Root Device.
  381. [ 4.573884] systemd[1]: Started Journal Service.
  382. [ OK ] Started Journal Service.
  383. Starting Remount Root and Kernel File Systems...
  384. [ 4.632019] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
  385. [ OK ] Started Remount Root and Kernel File Systems.
  386. Starting Create Static Device Nodes in /dev...
  387. Starting udev Coldplug all Devices...
  388. Starting Flush Journal to Persistent Storage...
  389. [ OK ] Started Create Static Device Nodes in /dev.
  390. [ OK ] Reached target Local File Systems (Pre).
  391. Mounting /var/volatile...
  392. Starting udev Kernel Device Manager...
  393. [ OK ] Mounted /var/volatile.
  394. [ 4.862561] systemd-journald[183]: Received request to flush runtime journal from PID 1
  395. Starting Load/Save Random Seed...
  396. [ OK ] Reached target Local File Systems.
  397. [ OK ] Started udev Kernel Device Manager.
  398. [ OK ] Started Flush Journal to Persistent Storage.
  399. [ OK ] Started Load/Save Random Seed.
  400. Starting Create Volatile Files and Directories...
  401. [ OK ] Started Create Volatile Files and Directories.
  402. Starting Update UTMP about System Boot/Shutdown...
  403. Starting Network Time Synchronization...
  404. [ OK ] Started Update UTMP about System Boot/Shutdown.
  405. [ OK ] Created slice system-systemd\x2dbacklight.slice.
  406. Starting Load/Save Screen Backlight...htness of backlight:backlight...
  407. [ OK ] Started Network Time Synchronization.
  408. [ OK ] Started udev Coldplug all Devices.
  409. [ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlight.
  410. [ OK ] Found device /dev/ttymxc0.
  411. [ OK ] Reached target System Initialization.
  412. [ OK ] Listening on RPCbind Server Activation Socket.
  413. [ OK ] Listening on GPS (Global Positioning System) Daemon Sockets.
  414. [ OK ] Started Daily Cleanup of Temporary Directories.
  415. [ OK ] Reached target Timers.
  416. Starting sshd.socket.
  417. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
  418. [ OK ] Listening on D-Bus System Message Bus Socket.
  419. [ OK ] Reached target System Time Synchronized.
  420. [ OK ] Listening on sshd.socket.
  421. [ OK ] Reached target Sockets.
  422. [ OK ] Reached target Basic System.
  423. [ OK ] Started Kernel Logging Service.
  424. [ 5.663802] imx_ipu_v3: exports duplicate symbol ipu_csi_init_interface (owned by kernel)
  425. [ OK ] Started System Logging Service.
  426. Starting Login Service...
  427. Starting Avahi mDNS/DNS-SD Stack...
  428. [ OK ] Started D-Bus System Message Bus.
  429. [ OK ] Started Avahi mDNS/DNS-SD Stack.
  430. Starting Network Service...
  431. Starting Save/Restore Sound Card State...
  432. [ OK ] Started Save/Restore Sound Card State.
  433. [ 6.215351] wl18xx_driver wl18xx.0.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
  434. [ 6.231382] wl18xx_driver wl18xx.0.auto: Falling back to user helper
  435. [ OK ] Started Network Service.
  436. [ 6.246772] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -11
  437. [ 6.261323] wlcore: WARNING falling back to default config
  438. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
  439. [ OK ] Reached target[ 6.333761] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Micrel KSZ8041] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
  440. Sound Card.
  441. [ 6.357353] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  442. [ OK ] Started Login Service.
  443. [ 6.651879] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
  444. [ 6.675141] wlcore: loaded
  445. Starting Load/Save RF Kill Switch Status...
  446. [ OK ] Found device /sys/subsystem/net/devices/wlan0.
  447. [ OK ] Started Load/Save RF Kill Switch Status.
  448. [ OK ] Started Attach WiLink8 Bluetooth Adapter hardwired to ttyO3.
  449. [ OK ] Started WPA supplicant daemon (interface-specific version).
  450. [ OK ] Reached target Network.
  451. Starting Network Name Resolution...
  452. Starting Permit User Sessions...
  453. Starting Network Time Service...
  454. [ OK ] Started Permit User Sessions.
  455. [ OK ] Started Getty on tty1.
  456. [ OK ] Started Serial Getty on ttymxc0.
  457. [ 7.261598] wlcore: PHY firmware version: Rev 8.2.0.0.236
  458. [ 7.366102] wlcore: firmware booted (Rev 8.9.0.0.69)
  459. [ 7.386110] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
  460. [ OK ] Started Network Time Service.
  461. [ OK ] Started Network Name Resolution.
  463. Poky (Yocto Project Reference Distro) 2.2.2 colibri-imx6 ttymxc0
  465. colibri-imx6 login:

bootlog