- ɱ�300b000.pinctrl: Looking up vcc-ph-supply from device tree
- [ 0.380447] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-ph-supply property in node /soc/pinctrl@300b000 failed
- [ 0.380503] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-ph not found, using dummy regulator
- [ 0.380980] printk: console [ttyS0] disabled
- [ 0.401855] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 14, base_baud = 1500000) is a 16550A
- [ 2.091962] printk: console [ttyS0] enabled
- [ 2.097185] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-pd-supply from device tree
- [ 2.105325] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-pd-supply property in node /soc/pinctrl@300b000 failed
- [ 2.115888] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-pd not found, using dummy regulator
- [ 2.126069] dwmac-sun8i 5020000.ethernet: PTP uses main clock
- [ 2.131853] dwmac-sun8i 5020000.ethernet: Looking up phy-supply from device tree
- [ 2.139272] reg-fixed-voltage gmac-3v3: Looking up vin-supply from device tree
- [ 2.146517] vcc-gmac-3v3: supplied by vcc-ac200
- [ 2.151583] dwmac-sun8i 5020000.ethernet: Current syscon value is not the default 58000 (expect 50000)
- [ 2.160917] dwmac-sun8i 5020000.ethernet: No HW DMA feature register supported
- [ 2.168156] dwmac-sun8i 5020000.ethernet: RX Checksum Offload Engine supported
- [ 2.175391] dwmac-sun8i 5020000.ethernet: COE Type 2
- [ 2.180366] dwmac-sun8i 5020000.ethernet: TX Checksum insertion supported
- [ 2.187164] dwmac-sun8i 5020000.ethernet: Normal descriptors
- [ 2.192833] dwmac-sun8i 5020000.ethernet: Chain mode enabled
- [ 2.198650] libphy: stmmac: probed
- [ 2.363700] dwmac-sun8i 5020000.ethernet: EMAC reset timeout
- [ 2.369388] dwmac-sun8i 5020000.ethernet eth0: stmmac_dvr_remove: removing driver
- [ 2.411553] dwmac-sun8i: probe of 5020000.ethernet failed with error -14
- [ 2.420492] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-pf-supply from device tree
- [ 2.428629] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-pf-supply property in node /soc/pinctrl@300b000 failed
- [ 2.439193] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-pf not found, using dummy regulator
- [ 2.449230] sunxi-mmc 4020000.mmc: Looking up vmmc-supply from device tree
- [ 2.456156] sunxi-mmc 4020000.mmc: Looking up vqmmc-supply from device tree
- [ 2.463135] sunxi-mmc 4020000.mmc: Looking up vqmmc-supply property in node /soc/mmc@4020000 failed
- [ 2.472539] sunxi-mmc 4020000.mmc: Got CD GPIO
- [ 2.502432] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
- [ 2.511616] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-pc-supply from device tree
- [ 2.519742] sun50i-h6-pinctrl 300b000.pinctrl: Looking up vcc-pc-supply property in node /soc/pinctrl@300b000 failed
- [ 2.530298] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-pc not found, using dummy regulator
- [ 2.540421] sun4i-usb-phy 5100400.phy: Looking up usb0_vbus-supply from device tree
- [ 2.548172] phy phy-5100400.phy.0: Looking up phy-supply from device tree
- [ 2.554978] phy phy-5100400.phy.0: Looking up phy-supply property in node /soc/phy@5100400 failed
- [ 2.563947] sun4i-usb-phy 5100400.phy: Looking up usb3_vbus-supply from device tree
- [ 2.571669] phy phy-5100400.phy.1: Looking up phy-supply from device tree
- [ 2.578476] phy phy-5100400.phy.1: Looking up phy-supply property in node /soc/phy@5100400 failed
- [ 2.587933] ehci-platform 5311000.usb: EHCI Host Controller
- [ 2.593542] ehci-platform 5311000.usb: new USB bus registered, assigned bus number 3
- [ 2.601403] ehci-platform 5311000.usb: irq 19, io mem 0x05311000
- [ 2.622335] ehci-platform 5311000.usb: USB 2.0 started, EHCI 1.00
- [ 2.629115] hub 3-0:1.0: USB hub found
- [ 2.632918] hub 3-0:1.0: 1 port detected
- [ 2.637648] ohci-platform 5311400.usb: Generic Platform OHCI controller
- [ 2.644308] ohci-platform 5311400.usb: new USB bus registered, assigned bus number 4
- [ 2.652158] ohci-platform 5311400.usb: irq 20, io mem 0x05311400
- [ 2.667487] mmc0: host does not support reading read-only switch, assuming write-enable
- [ 2.680134] mmc0: new high speed SDHC card at address aaaa
- [ 2.686758] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
- [ 2.695508] mmcblk0: p1 p2
- [ 2.719034] hub 4-0:1.0: USB hub found
- [ 2.722851] hub 4-0:1.0: 1 port detected
- [ 2.727726] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
- [ 2.738840] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
- [ 2.744614] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5
- [ 2.753651] hub 5-0:1.0: USB hub found
- [ 2.757453] hub 5-0:1.0: 1 port detected
output of uart..
errors on Ethernet, vcc and so on..
help..in the dts?